Thundermax PN#309-366 - GenII V-Rod Manual de usuario descargar pdf

www.Thunder-Max.com

309-466 Installation / Setup Guide V2013.09.16

tmaxupport@thunder-max.com

Part # 309-366 / 309-466 for V-Rod®

Models

Thank you for purchasing a ThunderMax ECM!

Please read through the following instructions before

beginning the installation procedure. Following these

instructions will ensure that the ECM is installed and

setup properly for optimal results. If you have any

problems or questions, please refer to the SmartLink

Tuning .pdf Manual, included on the CD (Help Menu)

with this package.

Step 1 Insert the SmartLink

CD into your computer.

SmartLink will automatically

open the InstallShield

Wizard when the computer

finds the CD-Rom. Follow

the instructions and install

the software on your

computer. If you do not have a serial port on your

computer for the communication cable, you will need to

use a USB to Serial converter (an inexpensive converter

is available from Zipper’s, #372-000). Install the included

driver disc at this time; follow the instructions given by

Installation / Setup

Guide

Please Note: This product is Legal in

California

only for racing vehicles which may never be

used

upon a highway.

The user shall determine suitability of the

product for his or her use. Installation and use on a pollution-

controlled vehicle constitutes tampering under the U.S. EPA

guidelines and can lead to substantial fines. Review your

application and check your local laws before installing.

Locate fuse box just

forward of the seat and

remove fuse labeled

“ECM

POW

ER” (center

fuse, right side).

Unplug and remove the

factory ECM from the

motorcycle (located just

behind the steering

stem).

Due to the tight restrictions of the location of the ECM on

2002-2005

model bikes:

the manufacturer of the converter for installation.

Option 1 - The

Step 2 Install the ThunderMax and AutoTune modules.

(See dielectric grease tip for ECU on bottom of page 7)

Due to the mounting location and space constraints on

the V-Rod® for the ECM, your ThunderMax system is

supplied with a separate AutoTune module. The

ThunderMax ECM mounts in the same location as the

factory ECM; the AutoTune module mounts separately.

2002-2005 MODELS

Step 2a

Remove the

seat, air box

cover and

front frame

side covers

(2) to expose

the airbox

and battery

area.

Remove the

airbox lid with

snorkel.

communication

cable can be

installed into the

communication port

of the ThunderMax

ECM

and

remain

attached

the

ECM and stored on

the motorcycle

(how you

route/store

the

cable is up to you, you can run it through the frame and

along the airbox housing and store it under the seat or

roll it up and store it under one of the side covers), or

Option 2 –(PREFERRED not required) Install

t h

ThunderMax Pigtail Communication Port Harness

( i n c l u d ed) and wire it to the ECM harness plug on

the motorcycle for an alternate port location.

Once option 1 or 2 is performed, install the ThunderMax

ECM to the motorcycle in the stock location. Plug the

main harness into the ECM and reinstall the ECM fuse.

1 2 3 4 5 6 7 8

Indice de contenidos

Pagina 1 - Installation / Setup

www.Thunder-Max.com 309-466 Installation / Setup Guide V2013.09.16 [email protected] 1 Part # 309-366 / 309-466 for V-Rod® Models Thank

Pagina 2

www.Thunder-Max.com 309-466 Installation / Setup Guide V2013.09.16 [email protected] 2 Either of these options will allow 2006-UP MODELS S

Pagina 3

www.Thunder-Max.com 309-466 Installation / Setup Guide V2013.09.16 [email protected] 3 Plug the 4-pin AutoTune connector into the gray

Pagina 4

www.Thunder-Max.com 309-466 Installation / Setup Guide V2013.09.16 [email protected] 4 Step 3 Load a Base Map to your SmartLink soft

Pagina 5

www.Thunder-Max.com 309-466 Installation / Setup Guide V2013.09.16 [email protected] 5 Step 4 From the ‘Tuning Maps’ Tree, click th

Pagina 6 - CLOSED LOOP PROCESSING

www.Thunder-Max.com 309-466 Installation / Setup Guide V2013.09.16 [email protected] 6 Step 8 Before restarting the engine, from tool

Pagina 7 - TIPS AND GENERAL INFORMATION

www.Thunder-Max.com 309-466 Installation / Setup Guide V2013.09.16 [email protected] 7 these settings within the live module should you

Pagina 8

www.Thunder-Max.com 309-466 Installation / Setup Guide V2013.09.16 [email protected] 8 • Several support features are located under the

Modelos relacionados PN#309-466 V-Rod | PN#309-364 - GenII XR1200 |

Comentarios a estos manuales

Sin comentarios

Thundermax PN#309-366 - GenII V-Rod Manual de usuario

Busca en linea o descarga Manual de usuario para Para Motocicletas Thundermax PN#309-366 - GenII V-Rod. ThunderMax PN#309-366 - GenII V-Rod User Manual Manual de usuario

Indice de contenidos

Modelos relacionados PN#309-466 V-Rod | PN#309-364 - GenII XR1200 |

Comentarios a estos manuales

Relacionado con productos y manuales para Para Motocicletas Thundermax PN#309-366 - GenII V-Rod